Analisis Kerusakan pada Chain Link Apron Feeder

Authors

  • Muhammad Surya Netrane Jagad Jagad Jurusan Teknik Mesin Universitas Sriwijaya
  • Nurhabibah Paramitha Eka Utami Jurusan Teknik Mesin Universitas Sriwijaya
  • Diah Kusuma Pratiwi Teknik Mesin Unsri

DOI:

https://doi.org/10.36706/jrm.v21i2.140

Keywords:

Chain Link, Apron Feeder, Dye Penetrant, Vickers, Metallography

Abstract

The use of an Apron feeder with a carrying capacity of 90 tons with a motor with a power of 55 KW and engine speed of 1500 RPM as a container for coal unloading results in train cars and then distributed to a belt conveyor for 24 hours. Based on Standard Operating Procedures (SOP), the apron feeder can accommodate 8 train carriages for 120 minutes of unloading coal. This process initiates the possibility of fatigue in the Apron feeder component, namely the chain link. This study aims to determine the cause of chain link damage in terms of micro structure and strength to the value of hardness by using chain link analysis samples from PT. Acid Hill. Metallographic testing showed the presence of a banded structure in the new sample and the presence of a martensite phase in the damaged sample material, causing the material to become stronger but brittle.

Downloads

Download data is not yet available.

References

T. Chandra, “Analisis Kerusakan Pada Bucket Apron Feeder,” Universitas Sriwijaya, 2019.

Y. K. Afandi, I. S. Arief, And Amiadji, “Analisa Laju Korosi Pada Pelat Baja Karbon Dengan Variasi Ketebalan Coating,” J. Tek. Its, 2015.

D. Radaj And S. Zhang, “Notch Effect Of Welded Joints Subjected To Antiplane Shear Loading,” Eng. Fract. Mech., 1992.

P. Trihutomo, “Pengaruh Proses Annealing Pada Hasil Pengelasan Terhadap Sifat Mekanik Baja Karbon Rendah,” J. Tek. Mesin Univ. Negeri Malang, Vol. 22, No. 1, Pp. 81–88, 2014.

R. R. Eka Febriyanti, Dedi Priadi, “Effect Of Increasing Warm Rolling Deformation Degree To Deformation Band Characteristic Of C-Zn 70/30 Alloy,” Vol. 16, No. M.I.Mat. Kost., P. 9, 2016.

S. Kirono, E. Diniardi, And I. Prasetyo, “Aalisa Perubahan Dimensi Baja Aisi 1045 Setelah Proses Perlakuan Panas ( Heat Treathment ),” Sintek J. J. Ilm. Tek. Mesin, Pp. 1–11, 2010.

I. Hatta, “Aplikasi Mikro Analisis Dan Fraktografi Untuk Menentukan Kualitas Produk Dan Penyebab Kerusakan Suatu Komponen,” Pros. Pertem. Ilm. Ilmu Pengetah. Dan Teknol. Bahan, Vol. 30, No. C, Pp. 175–180, 2012.

Downloads

Published

2021-09-01

How to Cite

Jagad, M. S. N. J., Utami, N. P. E. ., & Pratiwi, D. K. (2021). Analisis Kerusakan pada Chain Link Apron Feeder. Jurnal Rekayasa Mesin, 21(2), 61–66. https://doi.org/10.36706/jrm.v21i2.140

Issue

Vol. 21 No. 2 (2021): Jurnal Rekayasa Mesin

Section

Articles

License

Copyright (c) 2021 Jurnal Rekayasa Mesin

Creative Commons License

This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

Jurnal Rekayasa Mesin (JRM) memberikan akses terbuka terhadap siapapun agar informasi dan temuan pada artikel tersebut bermanfaat bagi semua orang. Semua konten artikel Jurnal ini dapat diakses dan diunduh secara gratis, tanpa dipungut biaya, sesuai dengan lisensi creative commons yang digunakan.