Perancangan dan Pembuatan Mesin Bending dan Notching
DOI:
https://doi.org/10.36706/jrm.v21i1.72Keywords:
Bending, Notching, Solidworks, ManufacturingAbstract
Bending and notching is a common process in manufacturing world as in vehicles chassis fabrication. But, the recent problem is the limited tools that needed to bend and notch pipes. The objective of this research is to fabricate a tool or production machine that could bend and notch pipes based on need by using three roll bending method. As for the notching angle of 0 to 60 and the diameter for notching cutting is 1 to 2 inch. There are some calculations on machine structure by using solidworks simulation such as stress analysis, von mises and factor of safety. There are three trials in bending process such as deflection from 1, 2 and 3 cm and on the other side, notching trials start from 0 to 60 . This notching and bending machine created with two functions. The bending process is conducted in the middle part while the notching process is in the top part of the machine. This machine has 70 cm length, 50 cm wide and 120 cm height and the total amount of cost spent for this machine is Rp. 9.009.500.
Downloads
References
A. Mustakim, “Rancang Alat/Mesin Pengerol Pipa,” pp. 32, 117, 2012.
A. Albana, “RANCANG BANGUN ALAT / MESIN PEMBENGKOK PIPA,” Politeknik Negeri Medan, 2014.
S. Kuntoro and M. Kabib, “Analisis Kekuatan Dies Frame Link Pada Mesin Roll Pipa 2 in Penggerak Hidrolik Dengan Metode Elemen Hingga,” Simetris J. Tek. Mesin, Elektro dan Ilmu Komput., vol. 9, no. 2, pp. 941–946, 2018, doi: 10.24176/simet.v9i2.2453.
T. A. Wibowo, W. P. Raharjo, and B. Kusharjanta, “Perancangan dan Analisis Kekuatan Konstruksi Mesin Tekuk Plat Hidrolik,” Mekanika, vol. 12, no. 2, pp. 63–70, 2014.
W. Marsis and I. Toro, “Perancangan Mesin Bending Dengan Memanfaatkan Sitem Dongkrak Hidrolik Sederhana,” J. Mesin Teknol., pp. 42–51, 2007.
Iqbal R Pamungkas, B. Sulaksono, M. Munandar, A. Suwandi, and M. F. Fajar, “Perancangan Mesin Tube Notcher Menggunakan Metode G. Pahl dan W. Beitz,” Teknobiz J. Ilm. Progr. Stud. Magister Tek. Mesin, vol. 9, no. 2, pp. 20–32, 2019, doi: 10.35814/teknobiz.v9i2.536.
F. Klocke, Manufacturing Processes 4 - Forming (RWTH edition). 2013.
F. Klocke, Manufacturing processes 1: turning, milling, drilling, no. 7858. 2011.
A. Mustakim, “Rancang Alat/Mesin Pengerol Pipa,” pp. 32, 117, 2012.
A. Albana, “RANCANG BANGUN ALAT / MESIN PEMBENGKOK PIPA,” Politeknik Negeri Medan, 2014.
S. Kuntoro and M. Kabib, “Analisis Kekuatan Dies Frame Link Pada Mesin Roll Pipa 2 in Penggerak Hidrolik Dengan Metode Elemen Hingga,” Simetris J. Tek. Mesin, Elektro dan Ilmu Komput., vol. 9, no. 2, pp. 941–946, 2018, doi: 10.24176/simet.v9i2.2453.
T. A. Wibowo, W. P. Raharjo, and B. Kusharjanta, “Perancangan dan Analisis Kekuatan Konstruksi Mesin Tekuk Plat Hidrolik,” Mekanika, vol. 12, no. 2, pp. 63–70, 2014.
W. Marsis and I. Toro, “Perancangan Mesin Bending Dengan Memanfaatkan Sitem Dongkrak Hidrolik Sederhana,” J. Mesin Teknol., pp. 42–51, 2007.
Iqbal R Pamungkas, B. Sulaksono, M. Munandar, A. Suwandi, and M. F. Fajar, “Perancangan Mesin Tube Notcher Menggunakan Metode G. Pahl dan W. Beitz,” Teknobiz J. Ilm. Progr. Stud. Magister Tek. Mesin, vol. 9, no. 2, pp. 20–32, 2019, doi: 10.35814/teknobiz.v9i2.536.
F. Klocke, Manufacturing Processes 4 - Forming (RWTH edition). 2013.
F. Klocke, Manufacturing processes 1: turning, milling, drilling, no. 7858. 2011.
T. V Rohit, P. S. Ashutosh, K. V Shriraj, P. P. Akash, and P. G. Shivam, “Design and Fabrication of Pipe Bending and Pipe Rolling Machine,” Int. J. Adv. Res. Ideas Innov. Technol., vol. 3, no. 2, pp. 561–565, 2017, [Online]. Available: https://www.ijariit.com/manuscripts/v3i2/V3I2-1373.pdf.
Schuler, Metal Forming Handbook, no. c. Germany: Springer, 1998.
T. P. J. C. Rusch and E. Holmes, “The tube and pipe journal - Notching tube and pipe - 3 common methods,” 2003.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2021 Jurnal Rekayasa Mesin
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
Jurnal Rekayasa Mesin (JRM) memberikan akses terbuka terhadap siapapun agar informasi dan temuan pada artikel tersebut bermanfaat bagi semua orang. Semua konten artikel Jurnal ini dapat diakses dan diunduh secara gratis, tanpa dipungut biaya, sesuai dengan lisensi creative commons yang digunakan.